Audio accessories · Banana plugs
A banana plug that does more than just plug in – it becomes a connection point itself: the Dynavox banana plugs with rear socket combine a classic spring contact with an additional banana socket at the end of the plug. A second banana plug can be inserted straight into the back – ideal for bi-wiring, a second set of speakers or a subwoofer’s high-level connection, without overloading the binding post with several cables.
The plugs are gold-plated and accept speaker cables up to approx. 6 mm in diameter – so even generous cross-sections fit. The cable is secured without soldering via a side screw terminal. The 30 × 11 mm grip sleeve makes plugging in and out easy, even on crowded rear panels. The set contains four plugs, two red and two black, supplied in a blister pack.
Rear socket
Stackable for bi-wiring, a second pair of speakers or a subwoofer
Cables up to 6 mm
Side screw terminal – no soldering at all
Gold-plated
Spring contact with oxidation protection for a secure fit
The banana socket at the rear makes these plugs particularly versatile. If a second cable is needed, simply insert its banana plug into the plug that is already connected – the connection is looped through. Especially on amplifiers with small or closely spaced binding posts, this is far neater than squeezing two cable ends into one terminal, where usually neither sits properly.
Typical uses are bi-wiring with separate cables for the treble and bass sections, connecting a subwoofer via its high-level input in parallel with the main speakers, or a quick comparison between two cables. Important: running two pairs of speakers in parallel on one amplifier output halves the total impedance. Check beforehand that the amplifier is rated for the resulting load.
The 19 mm contact pin works as a spring plug: its sprung contact zone presses against the inner wall of the socket when inserted, giving a noticeably firm fit. This is the proven principle of the classic banana plug – simple, robust and compatible with all standard banana sockets on amplifiers, receivers and speakers.
The gold plating protects the contact surfaces from oxidation. Gold does not tarnish, so the contact resistance between plug and binding post stays low even after years. Especially on speaker connections, which carry comparatively high currents, a clean, corrosion-free contact is the basis for low-loss transmission.
Assembly needs no soldering iron. Strip the speaker cable, twist the strands tightly and insert them into the plug until no individual wires stick out. Then tighten the side screw until the conductor is securely clamped. Do not tin the strands: tin gives way under screw pressure over time and the clamp loosens. Bare, neatly twisted strands hold more firmly in the long run.
Observe polarity when connecting – red to positive, black to negative, on amplifier and speakers alike. Retightening the screw after a few weeks is recommended, as copper strands settle slightly under pressure. Some amplifiers leave the factory with plastic plugs in the binding posts, which must be removed before plugging in.
Frequently asked questions
What is the socket on the back of the banana plug for?
Another banana plug can be inserted into the rear socket of the Dynavox banana plugs. This lets you connect two cables to the same binding post, for example for bi-wiring, a subwoofer with a high-level input or a second pair of speakers.
What cable size fits the plugs?
The Dynavox banana plugs with socket accept speaker cables up to approx. 6 mm in diameter. This makes them suitable for thicker cables with a large cross-section too.
Do I have to solder the banana plugs?
No, the cable is clamped via a side screw terminal. No soldering iron or solder is needed.
Can I connect two pairs of speakers via the plugs?
Technically yes – a second pair can be connected in parallel via the rear socket. This halves the impedance at the amplifier output, for example from 8 to 4 ohms. Check beforehand that the manufacturer rates the amplifier for this load.
What is a spring banana plug?
A spring banana plug has a contact pin with a sprung contact zone. When inserted, the spring presses against the inner wall of the socket, ensuring a firm hold and good electrical contact.
How many plugs do I need for a stereo speaker cable?
A set of four plugs covers two speaker cables at one end, for example on the amplifier side. For two cables with plugs at both ends, you need two sets.
| Manufacturer |
Dynavox |
| Type |
Spring plug with socket |
| Connection |
Screw terminal (side), solderless |
| Rear |
Banana socket, stackable |
| Max. cable diameter |
approx. 6 mm |
| Finish |
Gold-plated |
| Contact pin length |
19 mm |
| Grip sleeve (L × Ø) |
30 × 11 mm |
| Quantity per set |
4 pieces |
| Colour coding |
2 × red / 2 × black |
| Application |
Speaker cables, bi-wiring, subwoofer (high-level) |
| Packaging |
Blister pack |