Audio accessories · RCA connectors
An RCA cable is only ever as good as its weakest link – and that is almost always the plug. If you want to make up your own cables, rescue a damaged end or cut a phono or RCA cable to exactly the right length, you need reliable plugs with a clean contact. The Dynavox RCA plug set of 4 delivers exactly that: four solder plugs with gold-plated contacts, clear channel marking and enough room for cables with an outer diameter of up to approx. 5.7 mm.
The set contains two red and two black plugs – enough for a complete stereo cable with both ends terminated. The colour coding identifies the right and left channel at a glance, so nothing gets swapped when connecting to an amplifier, phono preamplifier or turntable. At around 40.8 mm long and 13 mm in diameter, the plugs stay compact enough for crowded rear panels, and the soldered joint ensures a permanently low-resistance transition between cable and contact.
Gold-plated contacts
Protection against oxidation for a signal contact that stays stable over time
Cables up to 5.7 mm
Suitable for most RCA, phono and coaxial cables
Complete stereo set
2 × red, 2 × black – one stereo cable with both ends
RCA connections carry line and phono signals at very low voltages – the signal from a phono cartridge in particular is only a few millivolts. Any contact resistance at the plug therefore has a direct effect: oxidised or dirty contacts can cause hum, crackling and dropouts on one channel. The gold plating of the contact surfaces prevents exactly that. Gold does not oxidise and keeps the contact resistance constant for years – even if the connection is plugged and unplugged often or left untouched for a long time.
Equally important is the connection between cable and plug. A soldered joint is mechanically secure and electrically the most direct path: inner conductor and shield are permanently bonded to the centre pin and ground, with no clamping points that can loosen over time. That is why many hi-fi DIY enthusiasts and workshops consistently use solder plugs when making up high-quality cables.
Assembly & soldering tips
Assembly is straightforward with a standard electronics soldering iron and a little patience. The most important step comes first: slide the plug sleeve onto the cable before soldering – forget this and you will have to undo the joint. Then strip the cable jacket, twist the shield and expose just enough of the inner conductor for it to sit neatly in the centre pin. Lightly tin both ends beforehand.
Solder the inner conductor to the centre contact (signal) and the shield to the ground tab. A good solder joint is shiny and flows completely around the wire; dull, grainy spots indicate a ‘cold’ joint and should be reworked. Do not heat the centre pin for too long so the insulation inside the plug is not damaged. Finally, use a multimeter to check that there is no short circuit between signal and ground – the cable is then ready for use.
The RCA plug – known as ‘Cinch’ in German-speaking countries – was developed in the 1940s by the Radio Corporation of America to connect turntables to amplifiers, and it remains the standard for analogue audio connections in the home to this day. The Dynavox set is correspondingly versatile: for interconnects between source components and amplifier, for phono cables from turntable to phono preamplifier, for subwoofer and digital coaxial cables, or as a replacement for a broken or loose plug on an existing cable.
The set is particularly useful when a cable is needed in a custom length or a high-quality cable is to be made up from the reel. The result is an interconnect that fits your system exactly – with no excess cable loops behind the rack.
Frequently asked questions
Which cables fit the Dynavox RCA plugs?
The Dynavox RCA plugs take cables with an outer diameter of up to approx. 5.7 mm. This covers most common RCA, phono and coaxial cables; very thick high-end cables should be measured beforehand.
What do the red and black markings mean?
On RCA connections, red usually marks the right channel and the second colour – black here – the left channel. The set contains two plugs of each colour, enough for a complete stereo cable with both ends terminated.
Do I have to solder the RCA plugs?
Yes, the Dynavox RCA plugs have solder terminals. Inner conductor and shield are soldered to the centre contact and the ground tab, giving a particularly secure connection with lasting contact reliability.
Do gold-plated RCA plugs improve the sound?
Gold-plated contacts do not oxidise and keep the contact resistance permanently low. This prevents typical faults such as hum, crackling or channel dropouts, which can develop over time with corroded plugs.
Are Cinch and RCA the same thing?
Yes, Cinch and RCA refer to the same connector. ‘RCA’ is the term used internationally, ‘Cinch’ the name common in German-speaking countries.
Can I use the set to make a phono cable for my turntable?
Yes, the plugs are suitable for phono cables between turntable and phono preamplifier. A cable with two ends per channel needs exactly one set of four; a separate ground wire is additionally connected with a spade lug.
| Manufacturer |
Dynavox |
| Type |
RCA plugs, set of 4 |
| Connection |
Solder terminals |
| Contacts |
Gold-plated |
| Quantity per set |
4 pieces |
| Colour coding |
2 × red / 2 × black |
| Max. cable diameter |
approx. 5.7 mm |
| Dimensions (L × Ø) |
approx. 40.8 × 13 mm |
| Applications |
RCA, phono, subwoofer and coaxial cables; cable repair |
| Packaging |
Blister pack |